ZEROPLAY Miter Bars (Double Pack)


ZEROPLAY
or buy separately
★ NEW Product
Limited Time only
ZEROPLAY
Miter Bars (Double-Pack)
What's Included:
- (2) Miter Bars
- (2) Miter Stops
100% Satisfaction Guaranteed
- Priority Mail Express: No delays.
- Priority Mail: 1-2 day delay. No delays for local delivery.
- First-Class Package Service: 1-2 day delay.
BUILD TABLE SAW SLEDS FAST
Fits any standard 3/4” x 3/8” T-miter slots. [Check compatibility]
The defining feature and flaw of aftermarket miter bars are one in the same - set screws. Frustrated with the difficulty of fitting miter bars with set screws, Founder and inventor, Henry Wang, set out to change it. He conceived a method of adjustment based on opposing wedges, that adjusted the entire bar evenly in a single motion. With its ONE-TOUCH CALIBRATION® and top-down installation, the age-old struggles of sled making had finally been solved.

Calibrate your miter bar with a single touch.
ZEROPLAY Miter Bars’ ONE-TOUCH-CALIBRATION® adjusts using a system of opposing ramps. The two halves expand and contract to fill the entire slot.
- Top-down installation lets you keep your sled square to the fence while you secure the ZEROPLAY Miter Bar for a hassle-free setup and precision cuts.
- Includes (2) ZEROPLAY Miter Bars for larger/longer sleds and (2) ZEROPLAY Miter Stops.
- Fits any standard 3/4” x 3/8” T-Track Miter Slots.

Will it fit my miter slot?
ZEROPLAY Miter Bars will fit any standard (3/4” x 3/8”) miter slot that measures between 0.73" and 0.79" wide and is at least 5/16" deep.
Compatible miter tracks include but not exclusive to ShopSmith, SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks.
*Not compatible with table saws with tabs cast into the top of the miter slot or 5/8" miter slots i.e. Ryobi or Craftsman.
Top-down installation for hassle free setup.

Top-down installation
Miter Bar secures to the sled from the top, allowing you to square it to the blade without taking it off the table.

Speed and vesatility
Miter Bars can be used in tandem for longer sleds or to engage both miter slots at the same time. Retrofit to your existing sled and move easily from jig to jig.
Use it around your whole shop.
Features.
ZEROPLAY Miter Bars (Double Pack)

MATCHFIT Dovetail Hardware Variety Pack

MATCHFIT Dovetail Hardware Variety Pack

MATCHFIT Dovetail Router Bit (1/2"-14°)

MATCHFIT Dovetail Router Bit (1/2"-14°)

MATCHFIT Dovetail Clamp (2-pack)

MATCHFIT Dovetail Clamp (2-pack)

MATCHFIT Dovetail Clamp Pro

MATCHFIT Dovetail Clamp Pro
What people are saying.
The adjustment is easy to make and there is no play at all!
Amazon's choice.
Very good experience.
Recommended by WOOD Magazine.
Build a fast accurate compound miter sled
Got questions?
Does the ZEROPLAY Miter Bar work with Shopsmith® miter tracks?
It depends. The miter slots vary in width from model to model. Measure your miter slot to ensure that it is at least .730" wide"
Will the ZEROPLAY work on my miter track?
The ZEROPLAY Miter Bar System works with both ‘T’ & ‘U’ shaped miter slots. The adjustable range is between 0.73″ – 0.785″ this means the width of the miter slot in which the Miter Bar will lay must be between these ranges. In detail, the very bottom part of a ‘T’ shaped miter slot must be within this specific range as well as a ‘U’ slot. Secondly, the thickness of the ZEROPLAY miter bar is 5/16″. Specifically, this means that the miter slot must be a minimum of 5/16” in depth. Moreover, considering a ‘T’ shape miter slot the area below the hinges must be 5/16″ or greater in depth, and considering a ‘U’ shaped miter slot the depth must be 5/16″ or greater. The ZEROPLAY Stop only works with ‘T’ shaped miter slots. All the same physical parameters apply to this product as the Miter Bar system; except of course only working on ‘T’ shaped miter slots.
I’m having trouble adjusting my miter bars - either too tight or too loose. Any tips?
If your miter bar fits well but becomes too tight when installed on a sled, you may have tightened the panhead screws too much. Overtightening those screws can cause the bars to compress and expand outward. Try putting a single strip of paper on the inside of one of the miter slots when adjusting the miter bars’ width. This should offset the compression that occurs during installation.
My table saw has tabs at the top of the miter slot. Will ZEROPLAY Miter Bars work on my saw?
No. The tabs will get in the way. Refer to the compatibility diagram here:

Will ZEROPLAY Miter Bars fit my saw?
ZEROPLAY Miter Bars will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0.73" and 0.79" wide and at least 5/16" deep.
Compatible miter tracks include but not exclusive to ShopSmith, SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks.
*Not compatible with table saws with 'Tabs' cast into the top of the miter slot or 5/8" miter slots i.e. Ryobi or Craftsman.
Specifications.
Models
Parts
- (2) Miter Bars
- (2) Miter Stops
Parts
- Miter Bar
Parts
- (1) Miter Bar
- (4) 1.5" Dovetail Track Screws
360-degree fence angles
ZEROPLAY Miter Bars and Stops will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0.73" and 0.79" wide and at least 5/16" deep.
Compatible miter tracks include but not exclusive to: SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks.
(Not compatible with table saws with 'Tabs' cast into the top of the miter slot or 5/8" miter slots i.e. Ryobi or Craftsman)
ZEROPLAY Miter Bars and Stops will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0.73" and 0.79" wide and at least 5/16" deep.
Compatible miter tracks include but not exclusive to: SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks.
(Not compatible with table saws with 'Tabs' cast into the top of the miter slot or 5/8" miter slots i.e. Ryobi or Craftsman)
ZEROPLAY Miter Bars and Stops will fit ANY standard (3/4” x 3/8”) T-Track miter slot that measures between 0.73" and 0.79" wide and at least 5/16" deep.
Compatible miter tracks include but not exclusive to: SawStop, Bosch 4100, Delta Unisaw, Powermatic, Rigid, Dewalt, and General 350 Tracks.
(Not compatible with table saws with 'Tabs' cast into the top of the miter slot or 5/8" miter slots i.e. Ryobi or Craftsman)
ZP9-B2S2
ZP9-B1
DV-360ZPB1
Designed and made in the USA
Designed and made in the USA
Designed and made in the USA